|
|
|
 |
|
M15D
front
- with 2 ø 40 bayonet tines -
effective lenght 1.10 m or 0.80 m as an option.
- folding tines as an option and adjustable
support as an option.
- capacity : 1500 kg
and so for : M15DL - M16D - M20D
|
|
|
 |
M12DR
- with 4 ø 35 bayonet tines
- effective lenght 1.10 m or 0.80 m as an option
- adjsutable with (locking by shafts) from
1.80 to 2.40 m to pick up round bales of up to ø 180 side by
side.
- capacity : 1500 kg
|
|
|
 |
|
M22G
- with 2 sets of rugged clamps = 8 tines in
all.
- designed to handle 1 or 2 round bales.
- gain in storage height because top bales
is extra.
- bale tipping by hydraulic tipper of the
telescopic handler.
- capacity : 1200 kg
Hydraulic connection on M22G :
choice of 3 possibilities
. single double acting supply for 2 clamps.
. 2 separate functions to operate either top clamp or bottom clamp
independently depending on operation to be performed.
.
SENSOR option on single double acting supply : the lower clamp first
then the upper clamp closes in turn but the bottom clamps open at the
same time...This is the setup for working fastest.
|
|
|
 |
|
M14G
- with a set of rugged clamps - 12 tines -
height 1.70 m.
- designed for handling 1 or 2 round bales
and 1, 2 or 3 square bales.
- grasps round bales on the cylindrical
side but on the flat side too.
- capacity : 1200 kg
|
|
|
|
|
M12G
- with set of rugged clamps - 8 tines.
- 1,10 m high - 25 mm curved
tines of treated steel at 150 kg/mm² - 440 mm long (530 mm as an
option).
- Altec clamps are compact, do not catch on
bales already in place and are easily withdrawn.
- thanks to the special profile of the
chassis the bale being stored stays in its position in the stack and
does not tip back or to the side when the clamp open.
- designed for 1 or 2 round bales and 1 or
2 square bales.
- grasps round bales on the cylindrical
side but on the flat side too.
- bale tipping by hydraulic tipper.
- compact and rugged chassis capacity 1200
kg.
|
|
|
 |
|
M12GS
As M12G above, multipurpose for round or square bales but:
- With 0.50 m hight - 3 positions mast -
locks with a pin.
- to move easily from onr position to
another tilt the mast to horizontal using the hydraulic tipper.
- on a large frontloader, allows 4th and
5th bales at a time.
- capacity : 1200 kg
|
|
| |
Lift height |
Capacity |
Bale pick up |
Rams |
Clearance |
Weight |
| M15D avant |
- |
1500 kg |
2 straight tines |
- |
0,90 m |
120kg |
| M12DR |
- |
1500 kg |
2 straight
tines |
- |
0,90 m |
180kg |
| M12G |
- |
1200 kg |
8 tine clamp |
1 DA |
1,10 m |
190kg |
| M12GS |
0,50
m |
1200 kg |
8 tine clamp |
1 DA |
1,10 m |
220kg |
| M14G |
- |
1200 kg |
12 tine clamp |
1 DA |
1,70 m |
230kg |
| M22G |
+
1 bale |
1200 kg |
8 tine clamp |
1 or 2DA |
1,80 m |
210kg |
|
